Diamond Audio Stage 3 Installation Guide | 2014+ Street Glide

Stage 2 Installation Video

6x9 Saddlebag Speaker Installation Video

Tools needed:

• Fender cover
• T20 torx bit
• T27 torx bit
• T40 torx bit
• 5/32 hex bit
• 2mm allen wrench
• Panel removal tool

Stage 2 Bundle Installation

Step 1

Remove the outer fairing:

• Place a fender cover over the front fender to protect the painted surface.
• Remove the four T27 torx bolts.
• There are two located on each side of the fairing.
• The shorter bolt is lower and long bolt is towards the top of the fairing.
• Remove the three T27 torx bolts from the top of the fairing along the windshield.
• Leave the longer bolt in the middle attached slightly to support the fairing.
• Remove the windshield.
• Remove the center bolt and remove the out fairing.
• Disconnect the headlight connector and completely remove the outer fairing.

Step 2

Remove the Right (Brake Side) speaker pod:

• Remove the power connection from the bottom of the speaker pod.
• Disconnect the speaker wire connector.
• Remove the three 7/16 inch bolts holding in the bottom inside of the pod.
• These are located near the forks.
• Using a T25 torx bit remove the two bolts attaching the speaker pod to the tray on top of the radio.
• Use a 3/16 allen to remove the three remaining bolts holding the speaker pod to the inner fairing.

Step 3

Remove the Left (Clutch Side) speaker pod:

• Disconnect the speaker wire connector.
• Remove the three 7/16 inch bolts holding in the bottom inside of the pod.
• These are located near the forks.
• Using a T25 torx bit remove the two bolts attaching the speaker pod to the tray on top of the radio.
• Use a 3/16 allen to remove the three remaining bolts holding the speaker pod to the inner fairing.

Step 4

Installing your new Diamond Audio 6.5 inch Horn Speakers:

• Remove the four T25 screws securing each speaker.
• Disconnect the wiring harness from the speaker prongs.
• You may need to gently wiggle them back and forth to release the spade connectors.
• Use the provided crossover, connect the 1/4 inch and 1/8th inch spade connector to the 1/4 inch and 1/8th inch prongs on the 6.5 inch speaker.
• Using the bare wire side of the crossover and the provided speaker wire pigtail, twist the red wires together and twist the black wires together.
• Insert the red wires into the red push terminal on the speaker.
• Insert the black wires into the black push terminal on the speaker.
• Connect the spade connector on the provided pigtail to the factory wiring from the speaker pod.
• Insert the speaker assembly into the speaker pod, being sure to line up the mounting holes.
• Secure the speaker into the pod with the provided black phillips head screws.
• We recommend starting all four by hand and than carefully tightening down with a screwdriver.

Step 5

Replace the speaker pods:

• Place the speaker pods back on the appropriate side of the fairing.
• Replace the three 7/16 inch bolts holding in the bottom inside of the pod.
• Using a T25 torx bit replace the two bolts attaching the speaker pod to the tray on top of the radio.
• Use a 3/16 allen to replace the three remaining bolts holding the speaker pod to the inner fairing.
• Reconnect the power connection on the right (brake side) speaker pod.

Step 6

Installing the amplifier mounting plate:

• Remove the four T25 screws from the top plate located in the center of the top plate over the radio.
• Place the provided amplifier mounting plate over top of the top plate, being sure to line up the four holes.
• Secure with the four factory T25 screws that you just removed.
• We recommend starting all four by hand and than carefully tightening down with a screwdriver.

Step 7

Installing the MSTLINK harness:

• Insert the male factory connection into the rear of the radio.
• Connect the female main connector to the factory main connector from the motorcycle.
• Connect the four pin molex connector with RCA's labeled Front Left & Front Right to the Front Input.
• Connect the four pin molex connector with RCA's labeled Rear Left & Rear Rights to the Rear Input.
• Connect the four pin molex connector with White & Grey wires to the Front Output.
• Connect the provided blue remote turn on wire.
• Connect the male bullet connector to the female bullet connector coming from the Diamond Audio head unit.
• Place the other end with the wire ferrel into the REM port on the amplifier and secure using a 2mm allen.

Step 8

Mounting the amplifier:

• The kit will come with a few mounting options:
• We will provided four velcro squares that can be used to mount the amplifier to the amplifier bracket.
• The kit will come with velcro sheets that can be used.
• You may choose to drill into the mounting plate and secure using screws.

Step 9

Running the power and ground wires:

• For this step you will need to remove the seats and gas tank to expose the wire chase.
• Remove your seat.
• Remove the T40 bolts that secure the ECU plate on top of the battery, disconnect the two connections on the ECU plate.
• Remove the two T40 bolts that secure the front of the gas tank, near the forks.
• Remove the two T40 bolts that secure the bottom of the gas tank by the battery.
• Remove the fuel line by sliding the collar up and than pulling straight down.
• We recommend having a towel handy as a small amount of fuel may drip when the collar is removed.
• Remove the vent lines and lift the gas tank up and off the motorcycle.
• Once the wire chase is exposed, remove the cover by lifting the tabs around the edges.
• Remove the 60 AMP fuse from the inline fuse of the provided power wire.
• Route the power and ground wires in the wire chase.
• The end with wire ferrel will connect to the amplifier.
• The end with ring terminals will connect to the battery.
• Route the wires through the fairing on the Left side (clutch side) and towards the amplifier.
• Place the wire ferrel on the red power wire into the 12V in port on the amplifier and secure the wire ferrel with a 2mm allen wrench.
• Place the wire ferrule on the black ground wire into the Ground port on the amplifier and secure the wire ferrule with a 2mm allen wrench.
• Clean up the wires on the wire chase, you can use a few zip ties to hold everything in place.
• Connect the power wire to the positive battery terminal.
• Connect the ground wire to the negative battery terminal.
• Insert the 60 AMP fuse back into the inline fuse holder.
• Secure any extra power and ground wire.

Stage 3 Bundle Installation

Tools Needed:

• Cutting tools (Jig Saw, Air Saw, Dremel), Whatever you are comfortable with!
• 1/8th inch drill bit
• 5/16th inch drill bit
• 5/64th inch drill bit
• 3/8th inch drill bit
• Phillips head screw driver
• Painters tape
• T25 Torx driver

Step 1

Remove all components and ensure that you received all the parts needed for the install:

• 6x9 Horn speakers
• Speaker grilles
• Speaker mounting baskets
• Speaker mounting ring
• Wiring for left and right speakers
• Wiring to connect the amplifier to the wiring for the left and right speaker
• Wire keeper covers and hardware

Step 2

Preparing the bag lids for cutting:

• Cover the front 2/3rds of the top of the bag lid with painters tape.
• Be sure to cover the top and sides of the bag lid.
• Grab the cut template from the box and fit the template to the top of the bag.
• The templates are side specific.
• The templates should fit tightly along the front of the bag and sit all the way down to the lip on the bag lid.
• Once you are happy with the fitment you can use some more tape to secure the template.
• Finally secure the template to the bag lid with screws through the two holes in the center of the template.

Repeat the process for the other bag lid.

Step 3

Cutting the bag lids:

• Use a 1/8th inch drill bit to make pilot holes.
• The pilot holes will be placed in the rounded holes in the template.
• We recommend drilling towards the inside of the template.
• Use a 5/16th inch drill to enlarge the pilot holes.
• Use the cutting tool of your choice to cut from hole to hole on the template.
• Do not cut through the template material just yet.
• We recommend cutting tight to the inside of the template. This will leave you extra material if you need to remove more for proper fitment.
• Once you have cut the lines out you can cut the template material between to finish the cut.
• Remove the tape holding down just the template. Leave the tape in place that is on top of the front 3/4th of the bag lid.
• Clean out the plastic trimmings from inside the bag.

Repeat the process for the other bag lid.

Step 4

Checking fitment of the speaker grille:

• Grab the speaker grille from the box and test fit to the outside of the bag lid.
• If the speaker grille is not sitting flush to the bag lid, check for areas that may need trimmed, sanded or both.
• Continue making fine adjustments until the speaker grille fits just right.
• Once you are happy with the fitment, you can remove all of the painters tape.

Repeat the process for the other bag lid.

Step 5

Mounting the speaker grille and brace:

• You will need four of the provided machine screws to mount the grille to the brace.
• Mount the grille on the outside of the bag lid and the brace on the inside.
• Use the machine screws to attach the inner brace to the speaker grille, we recommend starting them by hand to ensure that all four are lined up before tightening them down.
• Install the speaker mounting ring to the inner speaker brace using four provided 3mm allen head screws.

Repeat the process for the other bag lid.

Step 6

Installing the 6x9 horn speakers:

• Place the 6x9 speaker on the inner brace and line up the four mounting holes.
• Secure the speaker with the provided phillips head screws.
• You can complete this step without removing the bag lid hold down but you can also remove it if you need more space to access the screws toward the rear. 

Repeat the process for the other bag lid.

Step 7

Routing the wiring for the speakers to the inside of the saddle bags:

• If you have not already done so, remove your saddlebags from the motorcycle.
• In the kit you will find two speaker wire protectors (Silver plates and hardware)
• Find a suitable mounting location and mark the three hole locations with a marker.
• Drill on the three marks with a 5/64th inch or smaller drill bit.
• In the middle of the three holes drill a 3/8th inch hole for the speaker wire.
• Place the speaker wire with the bare wire through the 3/8th inch hole to the inside of the saddlebag.
• Leave enough wire inside the bag to be able to both mount it out of the way and enough to reach the speaker.
• Place the wire protector over the speaker wire and secure with the three small phillips head screws. These only need to be hand tight, so no need to use a power tool.

Repeat the same process for the other saddlebag.

Step 8

Connecting the speaker wires and crossover:

• Use the provided crossover, connect the 1/4 inch and 1/8th inch spade connector to the 1/4 inch and 1/8th inch prongs on the 6x9 speaker.
• Using the bare wire side of the crossover and rear speaker wires, twist the red wires together and twist the black wires together.
• Insert the red wires into the red push terminal.
• Insert the black wires into the black push terminal.
• Mount the crossover to the speaker with the provided velcro.

Repeat the same process for the other saddlebag.

Step 9

Re-install the saddlebags onto the motorcycle:

• Choose a path to route the speaker wire from the bag lids to get them under the seat.
• This path may vary depending on your motorcycle or personal preference.
• Mount the saddlebags back onto your motorcycle. Secure with the locking pins.
• Connect the Left (Clutch side) to the harness with Green and White wires
• Connect the Right (Brake side) to the harness with Red and Black wires.
• Secure any extra or loose wire with zip ties and tuck away any extra wire, as to not interfere with mounting the gas tank or seat.

Step 10

Check the functionality of your Stage 3 bundle:

• Turn the ignition on so that the radio powers on.
• Find a song that will play for at least a few minutes.
• Turn up the volume on your head unit to about 75% of the MAX volume.
• Using a small flathead screwdriver adjust the Front Gain (Front Speakers) until your desired sound level is reached. Repeat for the Rear Gain (Bag Lid Speakers).
• You can make any other EQ settings changes with in the head unit.

Step 11

Reassembling the motorcycle:

• Manage any loose wires: under the seat, in the wire chase or inside the fairing.
• Replace the bolts that secure the ECU tray.
• Reconnect the 2 connectors on top of the ECU tray.
• Replace the chase cover.
• Replace the gas tank.
• Replace the four T40 bolts that secure the gas tank.
• Run the vent lines for the gas tank.
• Reconnect the gas line by pulling the collar back and pushing back into place.
• Replace you seat.

Step 12

Replace the outer fairing:

• Reconnect the headlight connector.
• Place the outer fairing into place and secure with the center windshield bolt.
• Replace the windshield.
• Replace the three T27 torx bolts from the top of the fairing.
• Replace the four T27 torx bolts.
• There are two located on each side of the fairing.
• The shorter bolt is lower and long bolt is towards the top of the fairing.
• Remove the fender cover over the front fender.

  
  Congratulations on installing your new
  Diamond Audio Stage 3 Bundle!